Stiffeners for Flex Circuits
August 10, 2023 | Mike Morando, PFC Flexible CircuitsEstimated reading time: 1 minute
One of the most recent topics in the flex world has been the evaluation of materials required to build a rigid-flex or flex circuit. Discussions around flex and materials include variations of polyimide and copper. Here I will discuss another material that plays a very important role in the world of flex circuits: stiffeners. These are critical components to a flex circuit because they broaden its scope and potential applications.
A “stiffener” in the flex circuit world is a generic term used to identify a material that prevents a flex circuit from bending and flexing. In all these instances, we will not be talking about rigid-flex—just flex circuits only. Stiffeners are, in most cases, a non-electrical component/addition to a flex circuit and function as a mechanical support.
Stiffeners are attached in a secondary operation by either thermal bonding, pressure sensitive adhesives (PSAs), or epoxy. Stiffeners require a secondary operation in the manufacturing process, so it is a cost adder.
Materials we have used to add stiffeners include FR-4, polyimide, aluminum, alumina, steel, and ceramic. As technology progresses and flex is used in more and different applications, a variety of materials are being used to support and create flex stiffeners.
Reasons to include stiffeners into your flex circuit design include:
- The SMT process and component support
- Through-hole component mounting
- Flatness requirements
- Mechanical infrastructure and design support
- Increased material thickness requirements
- ZIF connector interface
- Heat dissipation
- Wire bond pads
Figure 1: Mechanical support for SMT connector.
FR-4 and polyimide stiffeners can be placed in panel form on top of the flex panel. The material is drilled, routed, and pressed onto the flex panel. The flex with the stiffeners, now attached and in place, get routed or lasered and removed from the panel.
Manufacturers will always try to attach stiffeners in panel form; it is the most cost-effective solution to adding stiffeners to flex. In some instances, there is a need to hand place the stiffeners, requiring a separate lamination process. This adds cost. Your manufacturer should help you to design the lowest cost solution.
To read this entire article, which appeared in the July 2023 issue of Design007 Magazine, click here.
Suggested Items
DuPont Showcases AI Innovations Featuring Advanced Interconnects at 2024 International Electronic Circuits Exhibition
05/13/2024 | DuPontDuPont announced it will showcase its comprehensive range of advanced circuit materials and solutions at the 2024 International Electronic Circuits Exhibition in Shanghai. With a product portfolio that includes fine line, signal integrity, power and thermal management, DuPont will exhibit at Booth #8L06 at the National Exhibition and Convention Center (NECC) from May 13 to 15.
MKS’ Atotech to Participate in ECTC
05/10/2024 | MKS’ AtotechAt this year’s 74th IEEE Electronic Components and Technology Conference (ECTC), MKS’ Atotech will present and demonstrate its latest product and service innovations.
The Chemical Connection: Reducing Etch System Water Usage, Part 2
05/02/2024 | Don Ball -- Column: The Chemical ConnectionIn my last column, I reviewed some relatively simple ways to reduce water usage in existing etch systems: cutting down cooling coil water flow, adding chillers to replace plant water for cooling, lowering flow rate nozzles for rinses, etc. This month, I’ll continue with more ways to control water usage in your etcher. Most of these are not easily retrofittable to existing equipment but should be given serious consideration when new equipment is contemplated. With the right combination of add-ons, it is possible to bring the amount of water used in an etch system to almost zero.
Designer’s Notebook: What Designers Need to Know About Manufacturing, Part 2
04/24/2024 | Vern Solberg -- Column: Designer's NotebookThe printed circuit board (PCB) is the primary base element for providing the interconnect platform for mounting and electrically joining electronic components. When assessing PCB design complexity, first consider the component area and board area ratio. If the surface area for the component interface is restricted, it may justify adopting multilayer or multilayer sequential buildup (SBU) PCB fabrication to enable a more efficient sub-surface circuit interconnect.
Insulectro’s 'Storekeepers' Extend Their Welcome to Technology Village at IPC APEX EXPO
04/03/2024 | InsulectroInsulectro, the largest distributor of materials for use in the manufacture of PCBs and printed electronics, welcomes attendees to its TECHNOLOGY VILLAGE during this year’s IPC APEX EXPO at the Anaheim Convention Center, April 9-11, 2024.